READER'S CHOICE AWARDS VOTE NOW

VOTE FOR YOUR FAVORITE TPMS IN THE READER'S CHOICE AWARDS CLICK HERE TO VOTE

(772) 463-6522

Trailer TPMS

The following instructions are applicable to all TireMinder Trailer models listed below. 

Replace a Transmitter (Learn Mode)

To replace a transmitter on the TireMinder Solar Powered Trailer TPMS, please use the following instructions:

  1. Remove the original transmitter you wish to replace from the valve stem.
  2. Make sure you are in Monitoring Mode. Monitoring Mode is the mode where you can switch between °F and °C by pressing and releasing the left button.
  3. Press and hold the left and right buttons on the top of the 5 seconds, release once you hear a beep.
  4. After the beep you will be in Learn Mode and see the top left tire blinking.
  5. Select the tire position you would like to replace by pressing and releasing the left or right buttons to move to different tire positions.
  6. Once at the desired tire position, press and hold the center button until you hear a beep and see “—“.
  7. Screw the transmitter onto the corresponding tire position. Within 12 seconds, you should hear a beep and see the new tire pressure.
  8. If you wish to replace additional tire positions, repeat steps 5 to 7 until you have replaced the desired tire positions.
  9. You will now need to return to Monitoring Mode. Press and hold the left and right buttons for 5 seconds, release once you hear a beep.
  10. You should now be back in Monitoring Mode. Confirm this by toggling the temperature using the left button.

Adjust Baseline Pressures (Baseline Pressure Setting Mode)

To adjust the baseline pressures, please use the following instructions:

  1. Make sure you are in Monitoring Mode. Monitoring Mode is the mode where you can switch between °F and °C by pressing and releasing the left button.
  2. Press and hold the center button on the top of the monitor for 5 seconds, release once you hear a beep.
  3. After the beep, you will be in Baseline Pressure Mode and see the top left tire position blinking.
  4. Select the tire position you would like to adjust by pressing and releasing the center button on the top of the monitor.
  5. Once at the desire tire position, press the right or left button to lower or raise the baseline tire pressure, respectively.
  6. If you wish to adjust additional baseline pressures, repeat steps 4 and 5 until you have adjusted all desired tires.
  7. You will now need to return to Monitoring Mode. Press and hold the center button for 5 seconds, release once you hear a beep.
  8. You should now be back in Monitoring Mode. Confirm this by toggling the temperature using the left button.

Add Transmitters to a New Monitor (Learn Mode)

To add your existing transmitters to a new monitor, use the following instructions:

  1. Make sure you are in Monitoring Mode. Monitoring Mode is the mode where you can switch between °F and °C by pressing and releasing the left button.
  2. Press and hold the left and right buttons on the top of the 5 seconds, release once you hear a beep.
  3. After the beep you will be in Learn Mode and see the top left tire blinking.
  4. Select the tire position you would like to add by pressing and releasing the left or right buttons to move to different tire positions.
  5. Screw the transmitter onto the corresponding tire position. Within 12 seconds, you should hear a beep and see the current tire pressure.
  6. If you wish to add additional tire positions, repeat steps 4 to 5 until you have added each desired tire position.
  7. You will now need to return to Monitoring Mode. Press and hold the left and right buttons for 5 seconds, release once you hear a beep.
  8. You should now be back in Monitoring Mode. Confirm this by toggling the temperature using the left button.

Delete a Transmitter (Learn Mode)

To delete a transmitter on your TireMinder Solar Powered Trailer TPMS, please use the following instructions:

  1. Make sure you are in Monitoring Mode. Monitoring Mode is the mode where you can switch between °F and °C by pressing and releasing the left button.
  2. Press and hold the left and right buttons on the top of the 5 seconds, release once you hear a beep.
  3. After the beep you will be in Learn Mode and see the top left tire blinking.
  4. Select the tire position you would like to delete by pressing and releasing the left or right button.
  5. Once at the desired tire position, press and hold the center button until you hear a beep and see “—“.
  6. Repeat Steps 4 and 5 until all tire positions that you would like to delete read “—“.
  7. You will now need to return to Monitoring Mode. Press and hold the left and right buttons for 5 seconds, release once you hear a beep.
  8. You should now be back in Monitoring Mode. Confirm this by toggling the temperature using the left button.

Complete Reset (Learn Mode)

To reset your TireMinder Solar Powered Trailer TPMS, please use the following instructions:

  1. Remove all transmitters from your valve stems.
  2. Make sure you are in Monitoring Mode. Monitoring Mode is the mode where you can switch between °F and °C by pressing and releasing the left button.
  3. Press and hold the left and right buttons on the top of the 5 seconds, release once you hear a beep.
  4. After the beep you will be in Learn Mode and see the top left tire blinking.
  5. Select the tire position you would like to reset by pressing and releasing the left or right button.
  6. Once at the desired tire position, press and hold the center button until you hear a beep and see “—“.
  7. Repeat Steps 5 and 6 until on tire positions that you would like to reset read “—“.
  8. Use the right or left button to select the tire position you would like to add back to the monitor. Note, if your system came with 4 tires, please use the transmitter marked 1 on the driver’s front position, 2 on the passenger front position, 3 on the passenger rear position, and 4 on the driver rear. If your system came with 2 transmitters, please use the transmitter marked 1 on the driver side, and the transmitter marked 2 on the passenger side.
  9. Once at the desired position, screw the transmitter onto the corresponding tire position. Within 12 seconds, you should hear a beep and see the new tire pressure.
  10. Continue adding the remaining tire positions until all transmitters are back on the valve stems and displaying pressure.
  11. Once complete, you will need to return to the Monitoring Mode. Press and hold the left and right buttons for 5 seconds, release once you hear a beep.
  12. You should now be back in Monitoring Mode. Confirm this by toggling the temperature using the left button.

Leave a Reply